15 June 2023

Correlation of relative phase shift of frequency, wavelength and period of oscillation in erroneous time dilation:

1. Time dilation represents the difference in elapsed time measured by two clocks under relativistic effects. Time dilation due to relative velocity is based on the Doppler shift, which is the change in frequency of a wave relative to the motion of an observer relative to the wave source, the equation is t' = t/√(1 - v²/c²). And the gravitational time dilation between two events measured by observers located at different distances from the gravitational mass, the equation is T' = T/√1−2GM/rc².

2. Experiments made in electronic laboratories on piezoelectric crystal oscillators show that the wave corresponds to time shift due to relativistic effects.

Gravity exerts a mechanical force on any object that deforms the object and pushes on the surrounding atoms. G-forces cause internal particles of matter to interact, resulting in stresses and deformation (strain). Using gravity, energy is obtained by the so-called piezo-method, which converts mechanical stress into electrical energy. Piezoelectric gravity devices can generate energy anywhere. 

We get the wavelength πœ† of a wave is directly proportional to the time period T of the wave, that is πœ† ∝ 𝑇, Time is called 𝑇, the period of oscillation. The reciprocal of the period, or the frequency 𝑓, in oscillations per second, is given by the expression 𝑓 = 1/𝑇 = πœ”/2πœ‹ = 𝐸/β„Ž = 𝑣/πœ†. Where h is Planck constant, 𝑓, 𝑣, πœ†, 𝑇 and 𝐸 respectively represent frequency, velocity, wavelength, time period and Energy of the wave.

Whereas the time interval 𝑇(𝑑𝑒𝑔) for 1° of phase is inversely proportional to the frequency (𝑓). We get a wave corresponding to the time shift. For example, 1° phase shift on a 5 MHz wave corresponds to a time shift of 555 picoseconds (ps).

We know, 1° phase shift = 𝑇/360. As 𝑇 = 1/𝑓, 1° phase shift = 𝑇/360 = (1/𝑓)/360. For a wave of frequency 𝑓 = 5 𝑀𝐻𝑧, we get the phase shift (in degree°) = (1/5000000)/360 = 5.55 π‘₯ 10Λ‰¹ΒΊ = 555 𝑝𝑠

Therefore, for 1° phase shift for a wave having a frequency 𝑓 = 5 𝑀𝐻𝑧, and so wavelength πœ† = 59.95 π‘š, the time shift (time delay) π›₯𝑑 = 555 𝑝𝑠 (approx.)

Time shift of the caesium-133 atomic clock in the GPS satellite: The GPS satellites orbit at an altitude of about 20,000 km. with a time delay of about 38 microseconds per day. For 1455.5° phase shift (or, 4.04 cycles) of a 9192631770 Hz wave; time shifts (time delays) π›₯𝑑 = 0.0000004398148148148148 π‘šs approx) or, 38 microsecond time is taken per day.

From the above, we concluded that the phase shifts of frequency due to gravitational potential differences or relativistic effects correspond to dilation of wavelengths of the clock oscillation, which show errors in the clock reading and are misrepresented as time dilation. Time dilation is actually wavelength dilation.

Foundations: 

1. When mechanical stress is applied to a piezoelectric crystal, the structure of the crystal is deformed, the atoms push around and the crystal conducts an electric current. The mechanical stress of a piezoelectric crystal is greatest in the ground state. In the case of a gravitational potential difference, there is less gravitational stress on a piezoelectric crystal, which correspondingly reverses the deformation of the structure, thereby pushing the atoms around, causing the crystal to conduct less electric current than in the ground state.

2. Effect of phase shift on relative frequencies versus time: The instantaneous phase (Ο•) represents an angular shift between two relative sine waves and is measured in degrees. A sine wave and a cosine wave are 90° out of phase with each other. After a time Ξ”t, the two relative sine waves are initially synchronized in phase but differ in frequency by Δω degrees per second, developing a differential total phase shift (ΔΦ). Eq. Given by: ΔΦ = Δω × Ξ”t.

3. Time distortion always arises from frequency phase shift and corresponding wavelength distortion but relativistic time dilation cannot be understood from frequency phase shift and corresponding wavelength distortion and therefore they do not follow the general rule. Relativistic time dilation failed to identify any cause of time distortion. Whereas, a combination of general wave equation and Planck's equation, has been able to successfully identify that there is an influence factor of distorted frequency due to relativistic effects. The distorted frequencies in the equation provide a relative value of time for the corresponding wavelength distortions. The phase is shifted in frequency and the corresponding wavelength distortion exactly matches the time distortion as in the expression Ξ» ∝T.

4. Due to relativistic effects, phase shift in frequencies distort wavelength. So wavelength is not invariant but we know time is invariant and as per Lorentz transformation too. The equation of time dilation due to relativistic speed, attempts to modify time t through the influence of velocity v. This is illegal operation in mathematics, as none can modify invariant t with the effect of velocity v or speed. So called time dilation is relativistic error and not change in T, in order to get time dilation t'.

Reference: Relativistic effects on phaseshift in frequencies invalidate time dilation II.


12 June 2023

Time is invariant but no clock is invariant under gravitational influence:

Is time Lorentz invariant? It is the same interval of proper time. It also follows from the relation between Ξ”s and that c²Ξ”Ο„ that because Ξ”s is Lorentz invariant, the proper time is also Lorentz invariant. 

Proper time Δτ, by definition, is the time measured by an observer in their own rest frame, we can say Δτ = Ξ”t and therefore Ξ”s² = c²Ξ”t² = c²Ξ”Ο„².

All observers in all inertial frames agree on the proper time intervals between the same two events.

So, how come time dilation t' possible when proper time t is Lorentz invariant? It cannot.

1. Considering t<t', where t' is not in the same scale of t, because of enlagement in t.  

Note: t' is not t+x or t-x, but it is t<t', where x is Ξ”tThe Ξ”t is infinitisimally small t.

2. The general rule is frequency represents time in inversed relationship f = 1/T = 1/Ξ», and wavelength equivalents period of time Ξ»∝T.

So wavelength Ξ» cannot be invariant but only T. 

Due to Relativistic effects, phase shift in frequencies distort wavelength. So wavelength is not invariant but we know time is invariant because Ξ”s is Lorentz invariant too.

3. Time dilation equation t' = t/√(1 - v²/c²) 

The equation attempts to modify t through the influence of velocity v. This is illegal operation in mathematics, as none can modify invariant t with the effect of velocity v or speed..

4. Experiment made on piezoelectric oscillator show that speed or gravity influence wavelength Ξ», and wavelength corresponds to period of time, so error occurs in T, as in the relationship Ξ»∝T.

Conclusion so called time dilation is relativistic error and not change in T, in order to get time dilation t'.

There is no dilation in time but in wavelength.

Time dilation is wrong and it's equation too.

Reference: https://doi.org/10.36227/techrxiv.22492066.v2

11 June 2023

Proof of Invariant time even in relativity:

Abstract:

Due to the relative effects on the phase shift of the frequencies, it is concluded that the error in the clock mechanism distorts the wavelength of the clock oscillation. This made wavelength covariant in events, but time was invariant because time is invoked by events.

Introduction:

In mathematics time and space are mathematical parameters. Relativity represents space and time as relativistic covariants, but the relativistic effects on phase shift of frequencies invalidates time dilation; and, presents relativistic time (a component of relativistic spacetime) as invariant.

The event of existence invokes time. According to the definition of the SI unit of time, the frequency of the cesium 133 atom must be 9192631770 Hz. equals to s¯¹, subject to undisturbed ground condition. This means, continuous frequency represents time

The research paper titled, 'Relativistic effects on phaseshift in frequencies invalidate time dilation II.' It states, the relativistic time emerge from relativistic frequencies. It is the phase shift in relative frequencies due to the infinitisimal loss of wave energy and the corresponding increase in the wavelength of oscillation; which occurs at any clock between relative locations due to the relativistic effects or difference in gravitational potential; resulting error in clock time reading; which is improperly represented as time dilation. 

Relationship between time and wave oscillation:

Time is called 𝑇, the period of oscillation. The reciprocal of the period, or the frequency 𝑓, in oscillations per second, is given by the expression 𝑓 = 1/𝑇 = πœ”/2πœ‹ = 𝐸/β„Ž = 𝑣/πœ†. Where h is Planck constant, 𝑓, 𝑣, πœ†, 𝑇 and 𝐸 respectively represent frequency, velocity, wavelength, time period and Energy of the wave.

Whereas the time interval 𝑇(𝑑𝑒𝑔) for 1° of phase is inversely proportional to the frequency (𝑓). We get a wave corresponding to the time shift. For example, 1° phase shift on a 5 MHz wave corresponds to a time shift of 555 picoseconds (ps). 

Experimental Result:

We know, 1° phase shift = 𝑇/360. As 𝑇 = 1/𝑓, 1° phase shift = 𝑇/360 = (1/𝑓)/360. For a wave of frequency 𝑓 = 5 𝑀𝐻𝑧, we get the phase shift (in degree°) = (1/5000000)/360 = 5.55 π‘₯ 10Λ‰¹ΒΊ = 555 𝑝𝑠

Therefore, for 1° phase shift for a wave having a frequency 𝑓 = 5 𝑀𝐻𝑧, and so wavelength πœ† = 59.95 π‘š, the time shift (time delay) π›₯𝑑 = 555 𝑝𝑠 (approx.)

Time shift of the caesium-133 atomic clock in the GPS satellite: The GPS satellites orbit at an altitude of about 20,000 km. with a time delay of about 38 microseconds per day. For 1455.5° phase shift (or, 4.04 cycles) of a 9192631770 Hz wave; time shifts (time delays) π›₯𝑑 = 0.0000004398148148148148 π‘šs approx) or, 38 microsecond time is taken per day.

Decision:

Time is the indefinite continued progress of existence and events in the past, present, and future regarded as a whole, succeeding in irreversible and uniformed succession, referred to in the fourth dimension above three spatial dimensions.

The undisturbed ground condition of continuous frequency represents time. However, wavelength distortions, due to the phase shift in relative frequencies correspond to time error; through the relationship πœ† ∝ 𝑇. 

Conclusion:

Therefore, it is concluded that the error in clock mechanism distorts the wavelength of the clock oscillation due to the relative effects on the phase shift of the frequencies; This made wavelength (πœ†) covariant in events, but time (𝑇) was invariant, because events invoke time and time as stated above is the indefinite continuous progression of existence and events.



Relativistic effects affects photons, and so, a hypothetical "Light clock" is not invariant:

A "single photon" can never bounce between two mirrors for the reasons mentioned below. A hypothetical 'light clock' is not demonstrable so such an undetectable clock is not accepted in physical science, because physical science is physical. Finally, the photon will be known as the bouncing event, and we know from the paper entitled, "Relativistic effects on phaseshift in frequencies invalidate time dilation II" that the event invokes time. Therefore, the so-called, light clock is not time itself, only events can invoke time. Events and time are completely different things. 

A photon exhibits an event of propagation wave. As every event has a consequence; so an incident photon will also have a similar consequence. A photon is subject to relativistic effects expending energy as it leaves the source of a gravitational well.

When a photon hits the mirror, the photon's energy is absorbed by an electron in the metal on the surface of the metallic backing mirror. As the incoming photon interacts with the free electrons of the metal and is absorbed. The electron then uses this extra energy to jump from a lower energy level to a higher one, moving further away from the atom's nucleus. A photon carries momentum, so each photon hitting the mirror causes an electron in the metal atom to absorb the original photon and emit a new photon with a different momentum, known as scattering. As the free electrons oscillate, a new photon is emitted and exits the mirror. So the photon is reflected and loses energy.

The lost photon energy: And we know from the paper entitled, "Relativistic effects on phaseshift in frequencies invalidate time dilation II" that, Relative time emerges from relative frequencies. It is the phase shift in relative frequencies due to infinitesimal loss in wave energy and corresponding enlargement in the wavelengths of oscillations; which occur in any clock between relative locations due to the relativistic effects or difference in gravitational potential; result error in the reading of clock time; which is wrongly presented as time dilation.

So called, a "Light clock" is not invariant, as relativistic effects affects photons.

Scientific interpretation of the above article:

Photon Interaction: When a photon collides with an atom on a mirror's surface, it can be absorbed by an electron, causing the electron to gain energy (hf) and move to a higher energy level. This process is similar to photoelectric absorption.

Mirror's Reflectivity: Mirrors are designed to optimize reflectivity by minimizing absorption (Ξ”E) to maintain high reflectivity. The reflected photon has energy hf−Ξ”E, where Ξ”E represents the energy lost within the mirror.

Angle of Incidence and Reflection: The angle of incidence (Θi) is equal to the angle of reflection (Θr). This relationship is also expressed in terms of angles in degrees (ΞΈi and ΞΈr), where ΞΈi+ΞΈr=180°.

Photon Energy Absorption: The difference in energy between the incident photon (Ξ³i) and the reflecting photon (Ξ³r) is Ξ”E, representing energy absorbed by the mirror. This energy difference is also equal to the time delay (Ξ”t) between the incident and reflecting photons.

Infinite Time Delay: When a photon is reflected by a mirror, there is an infinite time delay (Ξ”t) between the colliding photon (Ξ³i) and the diffusing photon (Ξ³r) to change the direction of travel. This phenomenon contributes to a time distortion in the behavior of light.

When a photon (hf) interacts with an atom on a mirror's surface, it can indeed be absorbed by an electron in the atom. This interaction results in the electron gaining energy (hf) from the absorbed photon. This increase in energy can cause the electron to move to a higher energy level within the atom, farther away from the nucleus. photoelectric absorption takes palce. Mirrors are made to minimize absorption (Ξ”E) in order to maintain high reflectivity.  optimize reflectivity (hf- Ξ”E) and minimize light absorption (Ξ”E). The reflected photon will have energy (hf- Ξ”E). The reflected photon will have an energy of (hf−Ξ”E).

The angle of incidence (Θi) is equal to the angle of reflection (Θr). Since, the angle of incidence (ΞΈi) is equal to the angle of reflection (ΞΈr), ΞΈi = ΞΈr; and, the sum of the angles of incidence (ΞΈi) and reflection (ΞΈr) always equals 180°, ΞΈi + ΞΈr = 180°. Therefore, if the angle of incidence (Θi) = 180°, so the, angle of reflection (Θr) = 180°. 

The reflected photon having energy (hf- Ξ”E) travels in the opposite direction of the interacting photon with energy (hf), the angle of incidence is equal to the angle of reflection. This means that the direction of the reflected photon is related to the direction of the incident photon but is not necessarily opposite to it.

In summary, incident photon energy (Ξ³i) = hf;  reflecting photon energy (Ξ³r) = (hf−Ξ”E); photon energy absorption (Ξ³i - Ξ³r) = (Ξ”E); 

So, when a photon of light at the speed of light strikes or collides with a mirror wall, initially, the photon is absorbed by electrons in the mirror's surface atoms. In effect, the collision causes another photon to detach from an electron in an atom on the mirror surface, and the detached photon travels at the speed of light but in the opposite direction to the colliding photon. As a result, some of the energy of the colliding photons is lost in the collision with the mirror surface. 

The reflected photon having energy (hf- Ξ”E) travels in the opposite direction of the interacting photon with energy (hf), at an 180° angle, when the angle of incidence was 180°. 

In summary, when a photon collides with a mirror surface, it is initially absorbed by electrons in the mirror's surface atoms. The collision causes another photon to detach from an electron in an atom on the mirror surface. The detached photon travels at the speed of light but in the opposite direction to the colliding photon. Some energy of the colliding photons is lost in the collision with the mirror surface. 

The energy of the incident photon is hf, where h is Planck's constant and f is the frequency of the photon. The energy of the reflecting photon is hf−Ξ”E, where Ξ”E represents energy loss due to interactions within the mirror. The difference in energy between the incident and reflecting photons is Ξ”E. This difference represents the energy absorbed by the mirror and not reflected.

The photon energy absorption = (Ξ³i - Ξ³r), the difference in energy between the incident and reflecting photons = Ξ”E.

Assuming, the incident photon frequency = f1; when, the incident photon energy = (Ξ³i); and, the reflecting photon frequency = f2; when, the reflecting photon energy = (Ξ³r); The change in energy between incident photon and reflecting photon = Ξ”E;

Given Equations:
Ξ³i−Ξ³r = Ξ”E (Infinitesimal loss in wave energy)
f1 = incident photon frequency
f2 = reflecting photon frequency
T(deg) = T/360 = (1/f)/360 = Ξ”t
f = E/h = 1/360*T(deg)
T(deg) = 1/f*360 = Ξ”t

So, the relationships are -
Ξ”E =Ξ³i−Ξ³r
Ξ”t=f1−f2

Thereofre,
Ξ”E = Ξ”t.

Since, Ξ”E = Ξ”t;

The change in energy (Ξ”E) is equal to the time delay (Ξ”t) between the incident photon and the reflecting photon . This suggests a relationship between the energy difference of the incident and reflecting photons and the difference in frequencies (f1 and f2) of those photons.

Therefore when, there is an infinite time delay (Ξ”t) between the colliding photon (Ξ³i) and the diffusing photon (Ξ³r) to change direction of travel. Therefore, the constancy of motion of a photon of light is broken when it is reflected by a mirror.

07 June 2023

Synchronization of atomic clocks:

As per SI unit of time, it's frequency that represents time. (The unit of time is defined by taking the fixed numerical value of the cesium frequency to be 9192631770 Hz.)

Atomic clocks are automatically synchronized to a radio signal that is continuously broadcast by the National Institute of Standards and Technology in the United States.

Atomic clocks are also subject to various external influences, including gravity.

Atomic clocks are used onboard GPS satellites orbiting the Earth, but must send updates twice daily to correct the clock's natural drift.
However, although the method is a simple correction of clock frequency depending on distance from Earth and other factors, the method is still inappropriate, as it is based on time distortion when it should be wavelength distortion.

It is the phase shift in the frequency due to the infinitisimal loss of wave energy under the relativistic effect on the clock mechanism, and other distortions.